Go to the source code of this file.
|
enum | AGSGeodeticCurveType {
AGSGeodeticCurveTypeGeodesic = 0
, AGSGeodeticCurveTypeLoxodrome
, AGSGeodeticCurveTypeGreatElliptic
, AGSGeodeticCurveTypeNormalSection
,
AGSGeodeticCurveTypeShapePreserving
} |
|
enum | AGSGeometryExtendOption {
AGSGeometryExtendOptionDefault = 0
, AGSGeometryExtendOptionRelocateEnds = 1 << 0
, AGSGeometryExtendOptionKeepEndAttributes = 1 << 1
, AGSGeometryExtendOptionNoEndAttributes = 1 << 2
,
AGSGeometryExtendOptionDoNotExtendFromStartPoint = 1 << 3
, AGSGeometryExtendOptionDoNotExtendFromEndPoint = 1 << 4
} |
|
enum | AGSGeometryOffsetType { AGSGeometryOffsetTypeMitered = 0
, AGSGeometryOffsetTypeBevelled = 1
, AGSGeometryOffsetTypeRounded = 2
, AGSGeometryOffsetTypeSquared = 3
} |
|
◆ AGSGeodeticCurveType
The different types of geodetic curves.
- Since
- 100
- See also
- About geodetic features
Enumerator |
---|
AGSGeodeticCurveTypeGeodesic | The shortest line between any two points on the Earth's surface on a spheroid (ellipsoid).
|
AGSGeodeticCurveTypeLoxodrome | A line of constant bearing, or azimuth.
|
AGSGeodeticCurveTypeGreatElliptic | The line on a spheroid (ellipsoid) defined by the intersection at the surface by a plane that passes through the center of the spheroid and the start and end points of a segment. This is also known as a great circle when a sphere is used.
|
AGSGeodeticCurveTypeNormalSection | A normal section.
|
AGSGeodeticCurveTypeShapePreserving | Keeps the original shape of the geometry or curve.
|
◆ AGSGeometryExtendOption
Flags for the type of extend operation to perform.
- Since
- 100.1
Enumerator |
---|
AGSGeometryExtendOptionDefault | By default, extension considers both ends of paths. The old ends remain and new points are added at the extended ends. The new points have attributes that are extrapolated from adjacent existing segments.
|
AGSGeometryExtendOptionRelocateEnds | If an extension is performed at an end, relocate the end point to the new position instead of leaving the old point and adding a new point at the new position.
|
AGSGeometryExtendOptionKeepEndAttributes | If an extension is performed at an end, do not extrapolate the end-segment's attributes for the new point. Instead, make its attributes the same as the current end. Incompatible with AGSGeometryExtendOptionNoEndAttributes .
|
AGSGeometryExtendOptionNoEndAttributes | If an extension is performed at an end, do not extrapolate the end-segment's attributes for the new point. Instead, make its attributes be empty. Incompatible with AGSGeometryExtendOptionKeepEndAttributes .
|
AGSGeometryExtendOptionDoNotExtendFromStartPoint | Do not extend the from end of any path.
|
AGSGeometryExtendOptionDoNotExtendFromEndPoint | Do not extend the to end of any path.
|
◆ AGSGeometryOffsetType
The different types of geometry offset joints.
- Since
- 100
Enumerator |
---|
AGSGeometryOffsetTypeMitered | Refers to a mitered joint type.
|
AGSGeometryOffsetTypeBevelled | Refers to a bevelled joint type.
|
AGSGeometryOffsetTypeRounded | Refers to a rounded joint type.
|
AGSGeometryOffsetTypeSquared | Refers to a squared joint type.
|